
Closed Loop Hall Effect Voltage Sensor
Voltage can be measured using current sensor to measure the small current flowing due to the voltage applied to a circuit with a large resistance. This current can be measured by an optimized Hall Effect voltage sensor based on digital technology. In practice, the resistance is often split into two with the Hall Effect voltage sensor in the middle to improve common mode rejection.
- Product Introduction
Wuxi Liou Electronics Co.,Ltd is one of the leading manufacturers and suppliers of closed loop hall effect voltage sensor in China. Our factory offer high quality customized products made in China with low price. Welcome to contact us for quotation.
Closed loop hall effect voltage sensors
S/N: VSM800DAT
Product overview:
Voltage can be measured using current sensor to measure the small current flowing due to the voltage applied to a circuit with a large resistance.This current can be measured by an optimized Hall Effect voltage sensor based on digital technology. In practice, the resistanceis often split into two with the Hall Effect voltage sensor in the middle to improve common mode rejection.

Features:
- Closed- loop (compensate) voltage transducer
- Capable measurement of DC and AC voltage with galvanic isolation between primary circuit and secondary circuit.
- Voltage measurement from 100 to 800 VRMS
Main characteristics:
- A unique design to cover all measuring ranges
- Low consumption and low losses
- Compact design
- Good behavior under common mode variations
- Excellent accuracy (offset, sensitivity, linearity)
- Good delay time
- Low temperature variation
Applications:
AC variable speed drives and servo motor drives
Static converters for DC motor drives
Battery supplied applications
Uninterruptible Power Supplies (UPS)
Switched Mode Power Supplies (SMPS)
Power supplies for welding applications
Renewable Energy (Solar and Wind)
Electric specs:
|
|
|||||||
|
Part No. |
VSM100DAT |
VSM220DAT |
VSM380DAT |
VSM500DAT |
VSM800DAT |
||
|
VPN |
Rated primary voltage |
100(AC) |
220(AC) |
380(AC) |
500(AC) |
800(AC) |
V(rms) |
|
VP |
Measuring range |
0~150% |
|||||
|
IOUT |
Rated output current |
20±1%(DC) |
mA |
||||
|
I0 |
Zero offset current |
4(DC) |
mA |
||||
|
RM |
Measuring resistor |
54~580 |
Ω |
||||
|
VC |
Power supply |
+24(±5%) |
V |
||||
|
Vd |
Dielectric strength |
Pri-Sec: AC2.5kVRms/50Hz/60s |
|||||
|
εL |
Linearity |
<0.2 |
%FS |
||||
|
X |
Accuracy |
TA =25℃ |
±0.8 |
% |
|||
|
IOT |
Thermal drift Zero offset current |
VP =0 TA =-25~+85℃ |
<±0.005 |
mA/℃ |
|||
|
Tr |
Response time |
<20 |
ms |
||||
|
TA |
Operating temperature |
-25~+85 |
℃ |
||||
|
TS |
Storage temperature |
-40~+100 |
℃ |
||||
|
m |
Weight(about) |
42 |
g |
||||
|
Standard |
Q/320115QHKJ01-2013 |
||||||
|
Dimensions(mm) |
|||||||
|
|
|||||||
|
Circuit diagram |
|||||||
|
|
|||||||
|
Use instructions |
|||||||
|
1.Incorrect wiring of the sensor may result in module damage. Once the sensor is powered, the voltage to be measured is connected to the input terminal of the sensor, and the corresponding current value can be measured at the output terminal. 2.Sensors with voltage output can be selected according to user requirements. 3.The output range of the sensor can be adjusted appropriately based on user needs. |
|||||||
Hot Tags: closed loop hall effect voltage sensor, China, manufacturers, customized, quotation, low price, made in China, Closed Loop Hall Effect Sensors, Hall Effect Sensor, Closed Loop Hall Effect High Current Sensor
You Might Also Like











